modern wood living room set
What's happening each person, i'm johnny brooke,welcome again to another crafted workshop video! In state-of-the-art video, i'm going to expose you howto build this ebonized white very wellmid-century present day nightstand. I love the manner this came out. The drawer frontreally makes this piece. I truely used my new laser cutter to reduce this geometric patternon the the front, and i just assume it is gorgeous. This style is best, kind of built it tothe peak of our mattress, and it suits pretty much flawlessly. I built a couple of these forour master suite right here and i'm simply excited to simply have a nightstand on my facet ofthe mattress. So let's pass ahead and get commenced with the build!
A couple of nightstands for our grasp bedroomhave been on my listing for a long time now. Genuinely, i???Ve been with out a nightstandon my facet of the mattress for approximately four years, that's form of ridiculous. How does thesaying pass? "the cobbler???S kids haven't any shoes." properly, in my case, the woodworker???Swife has a crappy ikea nightstand. Anyway, i had a few leftover white all rightfromthe arts and crafts eating chairs i constructed a little whilst returned, and it turned into nearly exactlythe amount i wanted for a couple of nightstands. Because most of the stock i bought forthat mission become 8/four, meaning that it became about two inches thick, it supposed that i hada lot of dimensioning and resawing to do, considering i wanted to apply ??" inventory for this mission.And that is what you???Ve seen me doing up
Subscribe to receive free e mail updates:
the motive i went with the timber ones wasthat i couldn't discover any drawer slides brief enough to fit this drawer. With any luck you men enjoyed this one! If youdid, cross ahead and get subscribed, i put out new tasks videos like this pretty muchevery week. I can additionally have plans to be had for this if you need to construct this for your self. I will have a listing of all of the tools and materialsi used in the video description underneath. Alright, thanks once more for looking guys and, untilnext time, happy building!
Drawer front, and then i introduced some screwsfrom within the drawer. With the drawers hooked up, the nightstandswere achieved! Okay, with a bit of luck you men enjoyed this one.This turned into a quite simple construct, i did have a little trouble getting the ones drawer slidesinstalled however i ultimately found out a terrific approach. The beveled front area honestly madeit tricky because i didn't have some thing to reference off of to get the ones drawer slidessquare. That was a piece of a trick but i'm certainly happywith the way it came out. The wood drawer slides certainly work genuinely well and theysaved me $15 in keeping with drawer slide so it is a nice reasonably-priced alternative.
I marked a center line the usage of a speed squareand measured in more or less 4 inches, then centered the bracket and delivered the includedscrews. With the legs hooked up, i moved directly to installingthe drawer slides onto the perimeters of the cabinet the usage of a few 1??? Screws. I made certain to pre-drilland countersink the holes, so that the heads of the screws had been under the surface of theslides. To make the drawers slide a touch less complicated,i brought a touch bit of paste wax to the drawer slides. I???Ll just reapply the wax periodicallyto preserve the drawers driving easily. Subsequent, i introduced the drawer fronts to the drawerboxes, the use of the playing card trick to area the drawer front lightly. The little handlecutout allowed me to get a clamp onto the
watched a lot of my videos, you know that ilove spraying on finishes, and the q3 is an superb hvlp gadget for this. The sheer quantity of adjustability inside the airflow, fan form, and quantity of fabric that???S passing via the gun allows you to reallydial for your completing, and making changes when finishing distinctive components of a projectis first-rate simple. To study extra about fuji spray and their line of hvlp systems, checkout within the hyperlink in the video description underneath. After the finish dried, it was time to assemblethe nightstands. First, i set up the legs. This was quite simple, i just needed to addthese brackets i picked up off of amazon. I???Ll have a link inside the video descriptionto the legs in addition to the brackets i used.
A similar leg would cost. $2.50. Yes, twodollars and fifty cents. I determined to scrap the concept of turning them myself and simply bought8 legs. Besides, lower back to the assignment, i determined toebonize the o.K.And, after a few research, found that some people have been using india inkfor this. I???Ll have a hyperlink within the video description to the exact ink i used, and ilove the manner it came out. I just wiped on a heavy coat using a shoptowel and let it dry in a single day. For the finish, i decided to spray on a fewcoats of a water based totally polyurethane in place of wiping it on, due to the fact i used to be afraid theink may bleed. To try this, i used my q3 platinum hvlp system through fuji spray, one ofthe sponsors of this week???S video. In case you???Ve
traced the form of the drawer front ontothe drawer container, cut it out with a jigsaw, and sanded it smooth. The ultimate pieces for the nightstands have been thehardwood drawer slides, which i cut from a scrap piece of tough maple i had handy. Theslides ended up at ????? Thick by using ????? Extensive. Now, you is probably asking your self, what aboutthe legs? And that???S a good query. I had actually firstly meant to turn sometapered legs at the lathe the usage of a few extra leftover okayi had. I spent some hours lastweek getting my lathe all set up, reducing up some leg blanks, and then getting two outof the eight legs grew to become. After completing the second one leg, i hopped onamazon surely brief, simply to peer how tons
subsequent, i reduce the drawer bottoms to length onthe table noticed and miter saw. To collect the drawer, i stored it truely simpleand simply used 1??? Brad nails and glue. That is kind of an experiment, to peer how the drawershold up without a other extra fasteners. I've a feeling they???Ll be simply exceptional. One little trick to cover the drawer bottomsfrom view is to chamfer the rims in order that the chamfer simply meets the bottom of the drawersides. It???S a really brief system and makes the drawers appearance a ton cleaner. Something i should have finished before assemblywas to cut a portion of the drawer the front so that the interior drawer field could be hiddenonce the drawer front is attached. I just
recognition location, the laser won???T harm the bedof the laser cutter even via it???S slicing over the edges. Whilst the laser cutter worked, i were given to workon the drawers. The drawer facets are made from ????? Plywood and the bottoms are madefrom ????? Plywood. I reduce the sides, fronts, and backs to size on the table noticed. I determined to apply hardwood drawer slides onthis build, considering the fact that i could not discover 11 inch drawer slides locally, and these drawers won???Texactly see heavy use. To do that, first i cut a ????? Huge groove into the drawer sidesto take delivery of the drawer slides the use of a dado stack. The intensity of the cut will depend upon your drawerslides, but i went with a ????? Deep groove.
Will come into contact with it, after which imoved over to the laser cutter. This is the entire spectrum muse, their newhobby laser. It???S were given a camera inside that lets in you to vicinity your art work on the pieceyou???Re laser engraving with quite correct accuracy. I discovered this geometric pattern on google imagesand simply dragged and dropped it into retinaengrave, complete spectrum???S software program. After gettingmy settings dialed in, i sent the process to the laser and it were given to engraving. This engraving technique took about 30 minutes,and i made positive that the artwork bled over the rims so it'd be a groovy edge-to-edgedesign. Since the laser most effective cuts in a small
i cut out the curve at the bandsaw, althougha jigsaw could work satisfactory if you don???T have a bandsaw, and then delicate the curve usingmy oscillating belt sander. Subsequent, i traced the curve onto the second drawerfront, reduce away the excess at the bandsaw, making sure to stay happy with my line, andthen moved over to the router table. I connected the drawer the front with the subtle curve tothe different drawer front with a few double sided tape, after which used a flush trim bit to cutthe second drawer front to in shape. Also, ignore the laser cut pattern right here, iforgot to reduce this pull cutout previous to laser engraving the primary drawer the front. We???Llget to that a little later. Next, i rounded over the top edges of thedrawer front, on account that this is in which your arms
as soon as the back panel dried, i chamfered thesides and back edges the use of my router. For the reason that front edges are already beveled, the chamferbit???S bearing didn???T have whatever to trip up towards, so i pulled out my trustyblock plane to chamfer the ones edges. Earlier than chamfering, the the front edges had been extremelyfragile, so i???D absolutely propose doing this. Additionally, chamfering edges with a blockplane is without a doubt one among woodworking???S greatest pleasures. With the cabinets completed, it turned into time to moveonto the drawers. For the drawer fronts, i desired to provide them an exciting aesthetic,so, after slicing the drawer fronts to length, i drew a little curve that could serve asthe drawer pull.
The back panel. I used a ????? Rabbeting bitand in all likelihood have to have made this reduce in passes. Alrightis extremely stringy and lovesto tear out in huge chunks, but happily i didn???T have any important troubles. Subsequent, i reduce the returned panels to size from somescraps of ????? Plywood i had available, after which rounded the corners with my random orbitsander in order that they???D in shape into the rabbet. I ought to have used a chisel to square up thecorners on the cabinet, but i find that sanding is generally surely a bit quicker. To attach the lower back panel to the nightstand,i used a little glue and some brad nails. And, pro tip, it facilitates to have your air compressorplugged in when using your brad nailer.
Cupboard like this, and you may pick out up a biscuitjoiner for as cheap as $60 new, or even less expensive used. In addition they add a very good bit of strengthto the mitered corners. After slicing the biscuit slots, i moved ontoassembling the carcass, which went quite easily. I clearly like to apply these strapclamps when assembling mitered carcasses, as they assist to keep things in region whilei upload clamps. One of the panels has bowed a little bit overnight, and the straps helpedpersuade the panels to lie flat all through the glue up. Once the glue dried, i eliminated the clamps,sanded off any glue squeeze out, and then moved over to the router table to cut therabbet into the back of the cabinet to simply accept
panels for my pair of nightstands while thefence was set, to make sure the measurement changed into exactly the identical on every panel. After trimming the top and bottom panels tolength, i repeated the same method for the sides, placing the fence to thirteen ?????. The last cut to make at the panels changed into a 45degree bevel at the front fringe of all the panels. That is optional, but i think thebevel at the front area is truly one among the biggest design elements of those nightstands.Offers it a absolutely cool look. To assist with meeting, i determined to feature somebiscuits in the corners of the nightstand carcass. Biscuits are extremely beneficial whenit comes to aligning the corners of a beveled
do???It???Yourselfer on account that 1948 with a wideselection of tools and system from all the primary producers. To research more, checkout the link in the video description below. After sanding, i squared up one stop of eachof the panels on the miter noticed. This square cease will journey towards the desk saw fencewhen reducing the bevels within the next step. Subsequent, i set my desk saw blade to forty five degreesand cut a beveled edge on every of the panels, riding the rectangular side up in opposition to the fence.At this point, i wanted to take as little off the panels as viable, as i desired tohave lots of room for very last trimming later. With a 45 degree bevel cut on one cease of eachpanel, i set my fence to 19 inches to trim my pinnacle and backside panels to very last length.I made certain to reduce all four pinnacle and bottom
this even on a 13??? Planer. As soon as the panels have been planed flat, i passedthem thru the drum sander to take away any device marks or snipe, and to get the panelssanded. Those sorts of tasks are virtually wherein the drum sander shines, as hand sandingall of these panels might have taken a long term. While i???M sanding, allow???S speak about oneof the sponsors of this week???S video, acme equipment. My drum sander, the supermax 19-38,became furnished by using my friends at acme gear, and i particularly inspire you check them outif you???Re thinking of buying any electricity equipment or different objects on your save. Acme toolshas served the contractor, woodworker and
till this point. If you wanted to construct this project your self,i???D advise simply using a few hardwood 1x8s, you???D save yourself a whole lot of work. Once i had my pieces down to roughly ?????Thick, i ripped them to rough width at the table saw, ensuring to leave a bit extrawidth for very last trimming afterward. With my pieces at their rough size, i gluedthem up into panels, making sure they stayed excellent and flat in the course of the glue up. After the glue dried, i flattened the panelsat the planer, evening up the two halves of the panels. For the reason that panels are so narrow,you have to in all likelihood be able to get away with